U.S.Saws

The Supreme Duty Dolly Manhole Cover Lift runs 10 in hard wheels under a collapsible frame and a lifting magnet, moving covers up to 36 in diameter...

The Curved Steel Dolly Manhole Cover Lift pairs a curved heavy duty collapsible steel dolly on 8 in hard wheels with a lifting magnet, moving cover...

The Hydraulic Hand-Held Saw is a fully welded aluminum-frame cut-off saw driven by a hydraulic motor on 12 GPM at 2,500 PSI, in three sizes cutting...

The Dual Component Polymer Pump dispenses polyurea and epoxy joint fillers from two 6.5 gallon semi-transparent tanks through a single-chain drive ...

The Big Belly Saw straps to large-diameter pipe and guides around the barrel for straight, controlled cuts, in two strap ranges covering 24 to 48 i...

The ACH-GB is a gearbox-driven air chainsaw for cutting pipe and concrete structures, running on 90 CFM at 90 PSI with no engine exhaust and no kic...

The VEX-400 is a portable battery valve turning machine that opens, closes, and exercises water system valves with 400 peak ft-lbs of torque throug...

The Valve Exerciser Hydrant Package is a battery valve turning machine configured for hydrant work: opening and closing valves during flow testing,...

The Ultra Vac 1250-P is a heavy duty certified-propane dust collector producing 450 CFM from a 14 HP Vanguard 408cc engine with electric start. It ...

The Ultra Vac 1250-G is a heavy duty gas-engine dust collector producing 450 CFM from a Honda GX240 and a high-output Airtec blower. It carries a 1...

The Ultra Vac 1250 is a heavy duty electric dust collector for concrete dust, producing 220 CFM from a pair of Ametek two-stage motors on standard ...

The TC-7-VS is the TC-7 Stand-Up Edger delivered as a polishing package: the same 15-amp Metabo-driven upright edge grinder equipped with a dust sh...

The TC-7 Stand-Up Edger is a walk-behind concrete edge grinder that gives the operator the control of a handheld grinder from an upright working po...

The PC7500 is a reversible plate compactor delivering 7,850 lbf of compaction force through an 18 x 28 in plate, traveling to 52 ft per minute forw...

The MC-800P Joint Hog is a walk-behind propane milling machine that removes spalled concrete joints up to 4 in wide and 1.75 in deep using closely ...

The MC-60 is a portable electric milling machine for removing spalled concrete joints and surface repair work. A 15-amp Metabo W26-230 grinder driv...

The Mark-IV Dust Buggy is an electric walk-behind saw for cleaning out control joints, removing old joint filler, and making straight cuts in concr...

The Aluminum Dolly Manhole Cover Lift pairs a collapsible aluminum-chassis dolly on 8 in hard wheels with a lifting magnet, moving covers up to 36 ...

The JS-160P is a certified-propane walk-behind joint clean-out saw that mills existing control joints for new fill or removes failed polyurea, epox...

The JS-131 is a gas walk-behind joint clean-out saw for milling control joints, concrete sawing, and trench cutting. It runs dry diamond blades to ...

The Hydraulic Belly Saw straps to pipes from 8 to 24 in diameter and pulls around the circumference for a straight, controlled cut on 5 to 7 GPM hy...

The HS Hand-Held Air Saw is a direct-drive cut-off saw that runs on 90 CFM at 90 PSI shop air instead of a gas engine, in two sizes: the HS-125 wit...

The FSB-150H is a hydraulic walk-behind saw that cuts to 7.5 in deep with blades up to 20 in, flush-cut capable, running on 12 GPM at 2,500 PSI. It...

The FSB-150 is an air-driven walk-behind saw that cuts to 7.5 in deep with blades up to 20 in, running a gearbox drive on 90 CFM at 90 PSI shop air...