Surface Preparation

The 5700DL is the 5700 carrying National's patented Dual-Lift front end, setting blade angle and pitch from the seat while the machine works. It we...

The 5625 is the compact propane rider, a 25 HP machine running up to 200 ft per minute on a 26 in frame. It carries the same drivetrain as the 5625...

The 5625DL is the compact propane rider with National's patented Dual-Lift front end, which sets blade angle and pitch from the seat with no stop. ...

The 550 is the smallest walk-behind scraper National builds, a 123 lb manual machine with a telescoping handle and an orbital cutting head. It take...

The 5280 Panther is a self-propelled walk-behind scraper at 263 lb, driven forward under its own power and pushed back by hand. Variable speed runs...

The 5200QL runs a slide-out replaceable battery pack accessed from the rear, so a discharged pack is swapped rather than charged in place. It has n...

The 5000DL is the compact rider in National's line, built on a low-profile frame that lowers transport height and tightens turning. Six AGM 200-amp...

The 3432 is a 10 lb handheld right-angle polisher taking a 5 in disk, with variable speed from 700 to 2,200 RPM. It ships with a loop handle, a vel...

The 2900 is National's high-speed battery ride-on scraper, running up to 160 ft per minute at 1,728 lb with 260 lb of that removable. It runs witho...

The 2900DL is the 2900 with National's Dual-Lift front end, which sets blade angle and pitch from the operator's seat with no stop and no tools. It...

The MC-1000 is a self-propelled, certified-propane joint clean-out saw and milling machine for removing failed joint fill and spalled concrete join...

The DC Tromb 600 Twin LL is Dustcontrol's largest single-phase twin dust extractor, pairing the machine cyclone with an integrated pre-separator on...

The DC Tromb 600 is Dustcontrol's largest single-phase dust extractor, running three single-phase fans on a 230 V, 60 Hz supply behind a tall cyclo...

The DC Tromb 400 Twin pairs a dust extractor with an integrated pre-separator on one 115 V chassis, so 80 to 90 percent of the coarse material drop...

The DC Tromb 400 is Dustcontrol's largest single-phase dust extractor on 115 V, moving 212 CFM through a cyclone, a self-cleaning washable polyeste...

The DC AirCube 2000 is Dustcontrol's largest air cleaner, circulating 1089 CFM of room air through a G4 cartridge pre-filter and a 108 sq ft HEPA H...

The DC 5900 is a three-phase 460 V dust extractor moving 471 CFM, built to feed a tubing system with up to four extraction points working at once. ...

The DC 2900 is a single-phase H-class dust extractor for source extraction from handheld tools and small table saws, moving 126 CFM on 115 V site p...

The Ultra Vac 1250-P is a heavy duty certified-propane dust collector producing 450 CFM from a 14 HP Vanguard 408cc engine with electric start. It ...

The Ultra Vac 1250-G is a heavy duty gas-engine dust collector producing 450 CFM from a Honda GX240 and a high-output Airtec blower. It carries a 1...

The Ultra Vac 1250 is a heavy duty electric dust collector for concrete dust, producing 220 CFM from a pair of Ametek two-stage motors on standard ...

The TC-7-VS is the TC-7 Stand-Up Edger delivered as a polishing package: the same 15-amp Metabo-driven upright edge grinder equipped with a dust sh...

The TC-7 Stand-Up Edger is a walk-behind concrete edge grinder that gives the operator the control of a handheld grinder from an upright working po...

The MC-800P Joint Hog is a walk-behind propane milling machine that removes spalled concrete joints up to 4 in wide and 1.75 in deep using closely ...